How to Repair Headphones

Any person has the headphones and not alone.The acquired for different purposes, for home use or travel in the subway painful, expensive or cheap, they have one drawback - the break.Familiar with the situation, when the wire frays, one earphone does not work, there are rattles and noise.Problem actually eliminated.This article will tell you how to fix the headphones with their own hands, while extending their service life.

repair headphones with your hands

If headphones are fed in, the sound disappears or changes, do not rush to the service center.Repair their own hands is real.First you need to determine why the earphones do not work.Damage often arises due to the fact that the wires are bent and broken their conductive cores.This is possible in Nokia headphones.Then you need to cut the wire, solder and clean.Buy a soldering iron and tin get in the store.

Prepare pliers and wire cutters to process headphone wires.If you want to ring for damage, you'll need a multimeter.You will need to buy a p

lug or connector, if you suspect that need to be replaced, or if torn headphones.Useful and glue with scissors.Glue is desirable to choose a flexible and quick-to plug.If one or both earphone noises appear, and then the sound disappears completely, then it means inner open wire strands.

There are other reasons why the headphones do not work.In a closed acoustic droplet type may occur channel blockage.In such devices, a membrane and a metal grid channel separated that is able to be contaminated.A sign of such damage will be no sound when the safety wire.Earphone disassemble and clean with alcohol.If you see a bounce, it indicates damage to the membrane.Open the device and inspect it.If the membrane is damaged or wrinkled, try to straighten it.If it dirt - wash with alcohol.

How to fix the headphones without a soldering iron?Without it will not work to create a good contact.Twist the wires, you make the headphones to work, but without soldering such repairs would be unreliable, and soon a favorite accessory stops work again, which will force you to spend money to buy a new one.

believed that the headphones Koss Porta Pro difficult to self-repair, but it is possible, if you follow the clear instructions.How to fix the earphone Apple's?With the elimination of the problems here will be easier.Headphones they are attached to the adhesive.Remove the gray rubber band from the head earphone or skovyrnite seam gluing.Finding the damage, cut, cleaning the damaged wire solder into place.

How to disassemble the headphones

for repair of large headphones will have to use a screwdriver to unscrew the screws.mid-size headphones are well hidden latch."Drip" headphones, usually just glued.Disassemble them actually using blade or lightly squeezing the headphones in a vice, in this case, the entire burden will fall on the line gluing.

How to fix a plug

plug wire breakage at the end headphones - a common problem.It leads to the fact that the accessory will be noise, crackles and pops, signaling that broke the conductive core.If you want to repair the headphone connector, consider some points.It can be coated one-piece plastic shell, or be cast rigid shape, covered with a rubber cap, which is contracted for the repair, or carefully cut off.

to break injection, need to use wire cutters, then it will be accessed to the pin terminals.Inspect wires, find a place gap and solder carefully.Since the plastic parts have to be removed, there may be empty spaces that are better pour quick-epoxy adhesive.The very design of wrap synthetic threads for greater strength.Note that problems often arise at the plug AKG headset.

connector Repair

you have already figured out how to fix the headset, however, there are problems with the connector?The return of the latter in the operation will require some of the details, which is better not to save.Although there are global standards, their fixation on the board can vary significantly.The common entrance is 3.5 mm.It is found in most modern music players, mobile phones, laptops, computers.In case of breakage connector has a chance to buy it in specialized stores radio and replace their own.

Repair wire

required fix wires?Then find a place where the rupture occurred.Sometimes you can not notice right away.In this case, you need to turn the sound on and bend the wire in different places, to understand where the problem occurred.Then you need to cut off the damaged part until the plug.Strip the ends on the wire, which is connected with a damaged, place the end of one of them, "tubing".Torsion and zaludit should weld them.If sound is restored, then slide the "tubing" and podplavte on both sides, protecting the joint.The same procedure, if the wire broke.

cable can get damaged and near the headphone itself.In this case, one of them stops working, or change the volume.There is a chance that will stop working immediately, both speakers.If this happens, the wire cut near the body, reveal, remember distribution wires, strip, using sidecutters or sandpaper, solder.Before you close the headset, check the sound, even a small breach of contact or fragile soldering can lead to noise, a bang.

with microphone for phone

All headphones have the same structure, with the only difference being that some or microphone volume control is added.Problems that may arise from them are the same as in conventional devices.The wire may be damaged, leaning, then you need to determine where it originated.Sometimes the wire is stretched, then you need to inspect it for reducing the thickness.

then wire should be cut and clean, where it has been damaged.With a sharp blade to gently make an incision around the wire.Themselves as conductive wires should get rid of varnish, by holding them over a flame.On the wire it is recommended to place a small piece of "cambric" for the subsequent creation of additional protection.Then you gently to tin and solder wires.

order to prevent their contact, use a little tape.Then slide the "tubing" and zaplavte.If the quality of the deteriorated recording microphone, there were noise or interference, it may mean that a microphone head is clogged, it could get the dust.It is necessary to moisten the cotton wool and alcohol to wipe the microphone carefully scraping the mud.Make sure that it does not remain the fabric fibers.


In case of violation of a contact directly on the plug or the dynamics do not even need to strip the wire again.Having examined the body to gain access to the speaker, or revealing the shell of the plug should be soldered injury site.If the problem is caused by physical damage to the speakers, resulting in a violation of the membrane, it is necessary to look for new same and put it in place of the failed.Find out how much it costs, and make the speaker in the service centers, or search the Internet space.


Repairs performed by replacing the buildings.Carefully disassemble the unit, in order not to damage the membrane, prepare a new shell.Tighten the wires to the nodes, strip, deal.Warm up their soldering iron to remove the old paint.If you decide to use the dynamics of the different pairs of headphones, it is recommended to measure their resistance to avoid unpleasant differences in sound and its volume.Solder the wires, close the case, then prepare to enjoy the music.

Video: how to repair headphones

These stories tell you how to fix a favorite accessory and how to disassemble Beats headphones, if they are broken, can not be mended, and find out what's inside, it would be desirable.You can amuse yourself and find out whether you are the original Monster Beats bought, or fake, and even accommodate small speakers mini speakers.After all, it is a pity to throw away, even if it can be for something accommodate thing.

How to fix headphones

How to disassemble the headphones Beats